Extrude attach tubes - hard times - Simply Maya User Community

# 1 30-07-2003 , 09:45 PM

Registered User
Join Date: Jul 2003

Posts: 22

Extrude attach tubes - hard times

I have 2 extruded tubes that end perpendicular to each other and I want to make a corner for the 2 ends or attach them to be one - can't seem to do it. any help would be great and you would be considered a legend in my book

PS I tried to attach the curves that make up the path for the extrucsion but it won't give me a clean 90 deg (perp.) corner when it make the transiton.

Thanks,
Moff

Quote

# 2 30-07-2003 , 10:12 PM

Moderator
Join Date: May 2003

Location: London

Posts: 1,001

hmm i think you can... bring in CV's closer to the join and it should become sharper.

or simply snap the cv's or use the fillet tool with the end isoparms of both tubes? im not to experienced with NURBS
Here is what u can get with freefrom fillet:

Attached Thumbnails

Click image for larger version

Name: guyhelpfillet.jpg
Views: 400
Size: 60.3 KB
ID: 9466

FX supervisor - double negative

Quote

# 3 30-07-2003 , 10:17 PM

Registered User
Join Date: Jul 2003

Posts: 22

That is exactly what I need! Er...I am going to try to get it to work now I will keep you posted should take long to figure out if it will work or not.

ty
Laurie

Quote

# 4 30-07-2003 , 10:55 PM

Subscriber
Join Date: Nov 2002

Location: USA

Posts: 1,170

Re: Extrude attach tubes - hard times

Originally posted by moffiosso
I have 2 extruded tubes that end perpendicular to each other and I want to make a corner for the 2 ends or attach them to be one - can't seem to do it. any help would be great and you would be considered a legend in my book

PS I tried to attach the curves that make up the path for the extrucsion but it won't give me a clean 90 deg (perp.) corner when it make the transiton.

Thanks,
Moff

Originally Posted by

extruding does sound like nurbs. so here is a workflow for nurbs (my version of it only others might have better idea). to make it easier, just create a 90 degree sharp corner between 2 cylinders.

step one: you have 2 cylinders (in my example simple lofts, but extruded should work as well) that are perpendicular and touching in one point as in upper left picture. you select the lower cylinder and duplicate the isoparm (rmb -> isoparm selection mask, select the upper isoparm, edit curves->duplicate curve)

step two: i hid everything from view that was not needed. now i select the newly duplicated isoparm (why not simply use my circle from the loft? well, you etruded, so you are unlikely to have that circle there already user added image

). now you move the pivot point to the position where both cylinder touch (with insert key, and then move with grid and/or curve snap to fit) so it is roughly in position as in upper right picture. this will gonna be where we let the tube go around the corner.

step three: now lets have some fun with animation. set a key at frame 1 for the circle. now go to frame 10 and rotate the circle so it aligns with the other tube (in my example 90 degree around z). set another key. now the circle should go perfectly 90 degrees around the corner at frame 1 through 10. now go back to frame 1, select the circle and create animation->animation snapshot. the default setting is fine, but check them. so that it starts at frame 1, ends at frame 10, and increment is 1. if you want more or less steps, just put the second key and the end of animation snapshot at different frame. looking pretty good, as in the lower left picture.

step four: select one circle of the animation snapshot (does not matter which one) and use the up-key to select the whole group. the very cool thing (and that is why i abuse it a lot to create lofts user added image

) about the animation snapshot is that after selecting the whole group the circles are picked in the correct order (starting from "frame" 1,2,3 .. 10). create a loft - and you are done. hide all curves, and unhide the hidden cylinders.

now it can happen that the corner and the 2nd cylinder dont align 100 % - to make them so, delete your 2nd extrude and redo with the last snapshot circle. you can now attach all 3 surfaces together or leave them as is or just globally stitch them together.

Attached Thumbnails

Click image for larger version

Name: extrude.jpg
Views: 341
Size: 64.1 KB
ID: 9468

Quote

# 5 30-07-2003 , 11:00 PM

Subscriber
Join Date: Nov 2002

Location: USA

Posts: 1,170

Originally posted by LauriePriest
hmm i think you can... bring in CV's closer to the join and it should become sharper.

or simply snap the cv's or use the fillet tool with the end isoparms of both tubes? im not to experienced with NURBS
Here is what u can get with freefrom fillet:

Originally Posted by

hehe, that works too - as many as answer as many solutions there is ...

Quote

# 6 30-07-2003 , 11:05 PM

Registered User
Join Date: Jul 2003

Posts: 22

Here is the condition...hope this helps

Attached Images

Quote

# 7 30-07-2003 , 11:13 PM

Subscriber
Join Date: Nov 2002

Location: USA

Posts: 1,170

Originally posted by moffiosso
Here is the condition...hope this helps

Originally Posted by

oh, that looks nasty. hope you find a way to clean that mess up. seams like you need more than just going around the corner, as the tubes already intersect. user added image