Maya for 3D Printing - Rapid Prototyping
In this course we're going to look at something a little different, creating technically accurate 3D printed parts.
#
1
26-08-2003
, 02:15 AM
Subscriber
Join Date: May 2002
Join Date: May 2002
Location: Faringdon, UK
Posts: 1,480
QuadroFX1000
my system specs:
asus a7n8x deluxe revision 2 (driver version 2.45)
athlon xp3200
quadrofx 1000 (driver version 44.71)
1.5gb DDR400 corsair low latency RAM (3 sticks of 512gb)
maxtor diamondmax plus9 SATA 8mb cache 120gb hard drive
antec trueblue 480watt PSU
audigy 2 platinum eX
creative 6.1 6700 speakers
windows 2000 SP4
i ran spec viewperk benchmark test and the results i get are lower than what they should be
spec viewperf 7.1 results:
3dsmax-02 Weighted Geometric Mean = 21.35
drv-09 Weighted Geometric Mean = 118.1
dx-08 Weighted Geometric Mean = 122.4
light-06 Weighted Geometric Mean = 27.59
proe-02 Weighted Geometric Mean = 32.10
ugs-03 Weighted Geometric Mean = 32.69
then i ran cinebench2003 and get these results:
**************************************************
**
Tester : Nem
Processor : AMD Athlon XP3200
MHz : 2.2ghz
Number of CPUs : 1
Operating System : Windows 2000 SP4
Graphics Card : QuadroFX1000
Resolution : <1600x1200>
Color Depth : <32bit>
**************************************************
**
Rendering (Single CPU): 272 CB-CPU
Rendering (Multiple CPU): --- CB-CPU
Shading (CINEMA 4D) : 308 CB-GFX
Shading (OpenGL Software Lighting) : 1348 CB-GFX
Shading (OpenGL Hardware Lighting) : 2557 CB-GFX
OpenGL Speedup: 8.31
**************************************************
**
they seem to be ok (right? i dont actually know much about benchmarking software)
and finally i ran specAPC for maya 5 and i get these:
graphics: 27.47
cpu: 1.92
I/O: 50.27
overall: 17.14
when on the site (www.specbench.org) it says that a quadroFX1000 card should be gettin:
graphics: 3.00
cpu: 2.28
I/O: 2.33
overall: 2.77
which means my computer is either above or below average, and im guessing below
how can i speed up the comp/graphics card? my main problem is the polygon limit in maya and XSI with the FX1000, i didnt think there was a poly limit, and if there was it shudnt be as low as 15000
btw, vsync was off when i performed these benchmark tests
#
2
26-08-2003
, 02:34 PM
Registered User
Join Date: Jul 2003
Join Date: Jul 2003
Posts: 51
I talked about em in another post.
https://forums.simplymaya.com/showthr...&threadid=7523
https://forums.simplymaya.com/showthr...&threadid=7466
At least they're not locking up or over heating
save often!
Joe
rasterfarian
#
3
26-08-2003
, 04:47 PM
Subscriber
Join Date: May 2002
Join Date: May 2002
Location: Faringdon, UK
Posts: 1,480
and its not about the saving, if it goes this slowly i have nothing to save
Posting Rules Forum Rules
Topics
New tutorial - Create tileable textures from photos. Photoshop to Alchemist to Maya 2
By David
Site News & Announcements
3
Free Courses
Full Courses
VFX News
How computer animation was used 30 years ago to make a Roger Rabbit short
On 2022-07-18 14:30:13
Sneak peek at Houdini 19.5
On 2022-07-18 14:17:59
VFX Breakdown The Man Who Fell To Earth
On 2022-07-15 13:14:36
Resident Evil - Teaser Trailer
On 2022-05-13 13:52:25
New cloud modeling nodes for Bifrost
On 2022-05-02 20:24:13
MPC Showreel 2022
On 2022-04-13 16:02:13