Introduction to Maya - Rendering in Arnold
This course will look at the fundamentals of rendering in Arnold. We'll go through the different light types available, cameras, shaders, Arnold's render settings and finally how to split an image into render passes (AOV's), before we then reassemble it i
#
1
15-07-2004
, 06:00 PM
Subscriber
Join Date: Apr 2004
Join Date: Apr 2004
Posts: 15
dynamic spline setup
If my question is confusing...let's say I am trying to make an animation of moving spagueti in a plate.
Thank you!!
I appreciate some clues...
#
2
15-07-2004
, 06:07 PM
Registered User
Join Date: Feb 2003
Join Date: Feb 2003
Location: Los Angeles
Posts: 695
If you are trying to...
... animate a whole plate of spagetti just moving a bit, you can apply a lattice to it, and then create clusters for some of the lattice points and animate the clusters.
... animate individual strings of spagetti you can apply the clusters directly to each piece and then aniate the clusters per strand.
I hope this helps.
#
3
15-07-2004
, 06:51 PM
Subscriber
Join Date: Dec 2002
Join Date: Dec 2002
Location: T.O Baby!
Posts: 1,016
#
4
16-07-2004
, 01:57 AM
Subscriber
Join Date: Apr 2004
Join Date: Apr 2004
Posts: 15
#
5
16-07-2004
, 02:37 AM
Subscriber
Join Date: Dec 2002
Join Date: Dec 2002
Location: T.O Baby!
Posts: 1,016
#
6
16-07-2004
, 05:46 AM
Subscriber
Join Date: Apr 2004
Join Date: Apr 2004
Posts: 15
I have gone so far as to create joins, give them CV's, give them IK handle, Make Selected Curves Dynamic, IK spline handle...and when I do the interactive dynamic, only the bones respond...not the polygons of a cylinder. The cylinder does not bend (for example).
I have tried to smooth skin the bones before or after the setup, but so far only the bones respond with no polygone surface effect. THANKS GUYS!
From the tutorial in MAYA I have done this:
Select Create > Curve CV Tool and trace a curve over the joints, clicking at each joint to create a CV. Press Enter at the end of the last joint.
With the curve selected, in the Dynamics menu set, select Hair > Make Selected Curves Dynamic.
Select Hair > Display > Current Position.
To attach the curve into the chain, in the Animation menu set, select Skeleton > IK Spline Handle Tool > .
In the IK Spline Handle Settings editor, turn off Auto Create Curve.
...the following follows but here I am lost:
Click the start joint.
Click the end joint.
Click the Current Position curve.
To select the follicle, do the following:
Select the curve.
Select the follicleShape node in the Attribute Editor.
Click the Select button at the bottom of the Attribute Editor.
In the follicleShape node, set Point Lock to Base.
To play the simulation, select Solvers > Interactive Playback.
Posting Rules Forum Rules
Similar Threads
IK Spline Issues
by sweetPotatoes in forum Maya Technical Issues replies 1 on 13-03-2014
Spline IK - Centipede
by OneAdamLeft in forum Maya Basics & Newbie Lounge replies 1 on 08-01-2013
Wire Setup Problems
by InvaZimm in forum Animation replies 4 on 11-01-2006
Spline IK and clusters
by greenleaf in forum Animation replies 4 on 09-11-2004
A spline by any other name. . .
by Binabik in forum Maya Basics & Newbie Lounge replies 11 on 05-10-2003
Topics
New tutorial - Create tileable textures from photos. Photoshop to Alchemist to Maya 2
By David
Site News & Announcements
3
Free Courses
Full Courses
VFX News
How computer animation was used 30 years ago to make a Roger Rabbit short
On 2022-07-18 14:30:13
Sneak peek at Houdini 19.5
On 2022-07-18 14:17:59
VFX Breakdown The Man Who Fell To Earth
On 2022-07-15 13:14:36
Resident Evil - Teaser Trailer
On 2022-05-13 13:52:25
New cloud modeling nodes for Bifrost
On 2022-05-02 20:24:13
MPC Showreel 2022
On 2022-04-13 16:02:13