Introduction to Maya - Rendering in Arnold
This course will look at the fundamentals of rendering in Arnold. We'll go through the different light types available, cameras, shaders, Arnold's render settings and finally how to split an image into render passes (AOV's), before we then reassemble it i
#
1
05-05-2015
, 05:44 PM
Subscriber
Join Date: Nov 2014
Join Date: Nov 2014
Posts: 4
Bend deformer along curve
I have been all over the internet trying to find the answer to this one and I've reached the end of my patience. What I am trying to achieve is pretty much what the standard bend deformer does but the only difference is I want it to unfold along a pre-defined curve. There are literally hundreds of tutorials about the bend deformer all doing the same thing, unfolding along a flat plane but none on how to do it along a curved surface. I have also tried paint effects with control curves to no avail and baking the bend deformer into the geometry then curving it afterwards. This last option didn't work as I no longer had the control I required. Bit of a grey area whether it belongs in animation or modelling but as it's a geometry deformer I chose modelling.
Any help on this would be greatly appreciated. Cheers
Last edited by scantillycladwell; 05-05-2015 at 05:48 PM.
#
2
05-05-2015
, 06:42 PM
The thin red line
Join Date: Aug 2009
Join Date: Aug 2009
Location: England
Posts: 4,472
Avatar Challenge Winner 2010
#
3
06-05-2015
, 10:13 AM
Subscriber
Join Date: Nov 2014
Join Date: Nov 2014
Posts: 4
Thanks for your reply. I had thought of that. But the design on top of which i'm trying to model has a lot of sharp corners and overlapping curves which cause the subsequent over lapping lattices created by the flow motion path to deform the geometry in crazy ways. See my image attached for an idea of what i'm trying to achieve. I want the final logo to look like it was created out of rolled out paper, similar to a quilling technique. I am trying to get tightly rolled up geometry to fold out along the curves in the image to reveal the logo. In fact the bend deformer does not seem up to the task as I cannot get tight enough rolls. It funny, I'm really shocked at how difficult this relatively simple idea seems to be.
#
4
07-05-2015
, 07:39 AM
The thin red line
Join Date: Aug 2009
Join Date: Aug 2009
Location: England
Posts: 4,472
Avatar Challenge Winner 2010
#
5
07-05-2015
, 08:33 AM
Subscriber
Join Date: Nov 2014
Join Date: Nov 2014
Posts: 4
Thanks for the reply. To go into details I want the rolled out paper/card to be coloured/textured on one side and white on the other with a depth in the y axis of 1 unit. I also want it mounted on a white piece of card so that from an above angle the logo can only be defined by 1. the colour bounce off the rear of the cards and 2. the shadows cast by the height of the cards like the image attached. 2.5D could do somewhat of a good job on the latter but not the former. At least in After Effects i'm not familiar enough with Nuke to make that kind of assumption. In any event Maya should be able to do what I require, I just need to find out how.
Last edited by scantillycladwell; 07-05-2015 at 08:58 AM.
Posting Rules Forum Rules
Similar Threads
Expression on Bend Deformer Problem
by Calvin in forum Programming replies 0 on 22-08-2016
Extruding face along existing curve or generated curve
by stwert in forum Maya Modeling replies 2 on 14-10-2012
Bend deformer and Painting Weight tool
by Ataraxy in forum Maya Basics & Newbie Lounge replies 0 on 05-02-2010
how do i bend a cylindar around a cv curve
by worfeus2000 in forum Maya Basics & Newbie Lounge replies 4 on 07-02-2005
Non-Linear Bend Deformer
by morlich in forum Maya Modeling replies 2 on 15-01-2003
Topics
New tutorial - Create tileable textures from photos. Photoshop to Alchemist to Maya 2
By David
Site News & Announcements
3
Free Courses
Full Courses
VFX News
How computer animation was used 30 years ago to make a Roger Rabbit short
On 2022-07-18 14:30:13
Sneak peek at Houdini 19.5
On 2022-07-18 14:17:59
VFX Breakdown The Man Who Fell To Earth
On 2022-07-15 13:14:36
Resident Evil - Teaser Trailer
On 2022-05-13 13:52:25
New cloud modeling nodes for Bifrost
On 2022-05-02 20:24:13
MPC Showreel 2022
On 2022-04-13 16:02:13